Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Ultramid® A3ZG7 OSI BK23273 - PA66-I-GF35 - BASF

Material Data Center offers the following functions for Ultramid® A3ZG7 OSI BK23273:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Ultramid A datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Processing/Physical Characteristics - 기계적 특성 - 열적 특성 - 기타 특성 - 도표
Any use of this information falls under the rules of our disclaimer.
제품 설명서
33% glass reinforced, heat stabilized, impact modified PA66 black with a combination of excellent impact resistance, toughness and strength.
Processing/Physical Characteristics건조/응축단위시험규격
ISO 데이터
성형 수축률, 평행 0.2 / * % ISO 294-4, 2577
성형 수축률, 수직 0.9 / * % ISO 294-4, 2577
기계적 특성건조/응축단위시험규격
ISO 데이터
인장탄성률 9340 / - MPa ISO 527
파단시 강도 147 / - MPa ISO 527
파단시 신율 4.9 / - % ISO 527
챠피 충격 강도 , +23°C 115 / - kJ/m² ISO 179/1eU
챠피 충격 강도, -30°C 117 / - kJ/m² ISO 179/1eU
챠피 노치드 충격 강도, +23°C 35 / - kJ/m² ISO 179/1eA
챠피 노치드 충격 강도, -30°C 21 / - kJ/m² ISO 179/1eA
열적 특성건조/응축단위시험규격
ISO 데이터
하중하에서의 변형온도, 1.80 MPa 246 / * °C ISO 75-1/-2
하중하에서의 변형온도, 0.45 MPa 259 / * °C ISO 75-1/-2
기타 특성건조/응축단위시험규격
밀도 1350 / - kg/m³ ISO 1183
도표
응력-신율 , Ultramid® A3ZG7 OSI BK23273 (건조), PA66-I-GF35, BASF
응력-신율 , Ultramid® A3ZG7 OSI BK23273 (응축), PA66-I-GF35, BASF
시컨트탄성율-신율 , Ultramid® A3ZG7 OSI BK23273 (건조), PA66-I-GF35, BASF
시컨트탄성율-신율 , Ultramid® A3ZG7 OSI BK23273 (응축), PA66-I-GF35, BASF
특징
인도 유형
검정
특별 특성
고충격 또는 고충격 보강
지역별 검색
쨘횕쩐횈쨍횧쨍짰횆짬
기타 정보
사E성
Nylon 66 materials must be properly dried in order to provide parts with optimum strength and toughness. Nylon 66 materials are hygroscopic and will become degraded by excessive moisture during the injection molding process. For unopened bag/box, dry at 60 degC (140 degF) for 1-2 hours. For material exposed to the atmosphere, if additional drying is needed, dry at 66 degC (150 degF) or until the moisture level is between 0.04 - 0.20%.

Typical Profile
Melt Temperature: 288-305 degC (550-581 degF)
Mold Temperature: 60-100 degC (140-212 degF)
Injection Pressure: 35-125 MPa (5000-18000 psi)


Back Pressure: 0-0.35 MPa (0-50 psi)
Screw RPM 40-80
Screw Compression Ratio:3:1-4:1


Mold Temperatures
This product can be processed over a wide range of mold temperatures; however, for applications where aesthetics are critical, a mold surface temperature of 60-100 degC (140-212 degF) is recommended.

Pressures
Injection pressure controls the filling of the part and should be applied for 90% of ram travel. Packing pressure affects the final part and can be used effectively in controlling sink marks and shrinkage. It should be applied and maintained until the gate area is completely frozen off.

Fill Rate
Fast fill rates are recommended to ensure uniform melt delivery to the cavity and prevent premature freezing.
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.